SIXAXIS / DUALSHOCK3 HID Minidriver (USB) Setting Application I am not good at English. Probably many errors will be included in contents. Please refer to Japanese explanation if possible. I use Yahoo! JAPAN-Honyaku for translation. ** Update ** version 1.4 Added inversion of the slider input. version 1.3 Supported the 64bit Windows. A save / load method addition of the setting. version 1.2 The specifications of the "Update" button were changed. (for Driver version 1.03) Introduction ------------ This software is a driver setting application for SIXAXIS / DUALSHOCK3 HID Minidriver (USB). Caution ------- This software is no guarantee. Please use it by a self-responsibility. System Requirements ------------------- 32bit Windows : Windows XP/Server 2003/Vista/7 64bit Windows : Windows Server 2003/Vista/7 It is necessary for a CPU to support x64(x86-64). x64 (x86-64) is the general term of the 64 bits operation processing technology. aka Intel64 (or EM64T) or AMD64. It does not support Intel Itanium series CPU. Install & Uninstall ------------------- The special operation is not necessary for install & uninstall. Copy files to a suitable folder. Delete files if not necessary. For Windows Vista/7 User ---------------------- When you validated UAC, a dialog is displayed at the time of an application start. Please admit it, and it is necessary for registry operation. Files ----- 32bit version : SDDriverSetting_e.exe 64bit version : SDDriverSetting_x64e.exe There is the case that extension is not displayed. Usage ----- Please set it to preference. OK - Save setting to registry. Cancel - Cancel setting. Update - Save setting to registry, and change the setting of the driver. If Bluetooth address is effective then, the application sets an address to a controller. But it is necessary to be connected by USB Menu File > Inport - Load setting from a file. > Export - Save setting to a file, You can name setting then. The maximum length for name is 32 characters. Device > Reset - Reboot a driver. > Get BD_ADDR - It retrieves address information from Bluetooth adapter. This function is for the adapter which a SIXAXIS/DUALSHOCK3 HID Minidriver (Bluetooth) driver was installed in. * After driver reboot, it is necessary to push the PS button once. Setting items ------------- 1.Interval Specifies interval of communication with the device, in unit of microsecond. Range : 850 - 100000 Default value : 8000 2.Enable Bluetooth Address Turn on a check if it is necessary to set Bluetooth address to a device. 3.Bluetooth Address Please input the address of the Bluetooth dongle. * Cannot use it by Bluetooth connection even if you set the above 2&3 4.Enable Advanced Mode When you set the addition, please turn on a check. But this is only for a DX edition. Additional Settings ------------------- 5.Axis tab Please choose the part of the device to assign to axes. -Invert If it is necessary to reverse an axis, you turn on a check. 6.HatSwitch Slider tab Please choose the part of the device to assign to Hat-Switch & Sliders. * 'Right side buttons' is a triangle, a circle, a cross and a square, these four buttons. -Four Direction Mode Limit a hat-switch to four directions. Default is eight directions. -Based on the center A start point of the input of the slider centrally. But a range becomes the half. -Invert If it is necessary to reverse an slider input, you turn on a check. 7.Output tab Choose an output characteristic. 'Linear' - Without converting input. 'Curve A' - The output is hard to change for input. 'Curve C' - The output is easy to change for input. 'D-Pad' - Like a Digital-Pad. 8.Dead Zone tab Specifies the threshold value of input of axes. Renge : 0-127 (0-100%) L2 and R2 trigger can set dead zone. It is applied at the time of button input mode. Renge : 0-255 (0-100%) 9.Buttons tab Choose the number to assign to each button. 10.Auto Fire tab -Enable Auto Fire Turn on a check if you use this function. -Function Button Choose a button to shift to auto fire setting. You can choose a plurality of buttons. -Speed Change In auto fire setting, you choose an analog stick to make a speed change. -Auto Fire Speed (per second) Specifies auto fire speed. The auto fire speed of the driver is not exact. 11.Axis2 tab -Change Axis Map Mode Turn on a check if you change an axial allotment method. But the content that you set in "Axis tab" becomes invalid. (The contents which you set in "Invert" are used.) Some items of the Output tab become invalid, too. 12.Input tab You can use this items if "Change Axis Map Mode" of the Axis2 tab is effective. Choose an input characteristic.(See also "Output tab") E-mail ------ E-mail address : tamamy_ikesu@yahoo.co.jp